JAMB UTME - Physics - 2024

Answer Details

 Measuring ionization current in air:
This is typically not a function of an electroscope. While it can detect charge, it does not measure ionization currents, which require specialized equipment like an ionization chamber.

Answer Details

The main feature of trees in the savanna habitat is the possession of thick, corky bark. The savanna is characterized by a distinct wet and dry season. During the dry season, fires are common as dry grasses and leaves become highly flammable. To adapt to this environmental condition, many trees in the savanna have developed a thick, corky bark which helps protect them against these frequent fires. This bark acts as an insulator, shielding the vital inner tissues of the tree from the heat of the flames. Additionally, this adaptation helps the trees retain moisture, which is crucial during the arid months when water is scarce.

Answer Details

When we say that the displacement of a car is proportional to the square of time (d ∝ t²), it indicates a relationship between displacement (d) and time (t). This relationship is characteristic of motion where there is constant acceleration. Essentially, it means that the car is not moving at a constant speed (velocity) but is accelerating at a constant rate.

The mathematical representation of this scenario can be expressed using the formula for displacement under uniform acceleration:

d = ut + (1/2)at².

In this equation:

• d = displacement
• u = initial velocity (which could be zero)
• a = acceleration
• t = time

When the displacement is directly proportional to the square of time (d ∝ t²), it implies that the second term of the equation, which contains the (1/2)at² part, dominates the relationship. Thus, the initial velocity (u) is typically zero or negligible, making the entire displacement dependent on how time squared interacts with acceleration.

Therefore, the car is moving with uniform acceleration.

Answer Details

When boiling water is poured into a thick glass tumbler, the inner surface of the glass is suddenly exposed to a much higher temperature compared to the outer surface. Glass is a poor conductor of heat, which means it does not transfer heat quickly. As a result, the inside of the tumbler becomes hot and attempts to **expand quickly**, while the outside remains cooler and does not expand at the same rate.

**This uneven expansion** creates tension between the inner and outer layers of the glass. The inner surface tries to expand but is constrained by the cooler, rigid outer surface, which isn't expanding as much or as quickly. This stress and tension can lead to cracking.

Therefore, the correct reason a thick glass tumbler cracks when boiling water is poured into it is because **the inside expands more rapidly than the outside.**

Answer Details

The simple form of the lead acid accumulator often has a negative pole of lead plate. In a lead-acid battery, the key components include two electrodes and an electrolyte. The **negative pole**, also known as the cathode during discharge, is typically made of **lead (Pb)**, which is in the form of a **lead plate**. When the battery is in use or discharging, this lead reacts with sulphuric acid (the electrolyte) to create lead sulfate.

To break it down further:

• **The positive pole** is usually composed of a lead dioxide (PbO₂) plate, which is sometimes referred to as lead peroxide.
• **The electrolyte** in the lead-acid battery is a diluted sulphuric acid solution, but this is not a solid pole or electrode.
• **The negative pole** is simply a solid **lead plate**, as noted earlier.

Thus, by analyzing the composition and reactions within a lead-acid battery, it is clear that the **negative pole** is made from a **lead plate**.

Answer Details

Bile is a greenish alkaline liquid that plays a crucial role in the digestive process, particularly in the digestion and absorption of fats. It is produced in the liver, but it is not stored there. Instead, the bile is transported to a small organ where it is concentrated and stored until the body needs it for digestion. This organ is the gall bladder.

The gall bladder stores the bile and releases it into the small intestine when food, especially fatty food, enters the digestive tract. This helps in breaking down the fats into smaller droplets, making it easier for enzymes to digest them.

To sum up, the gall bladder is the organ responsible for storing bile.

Answer Details

To solve this problem, we need to determine how far the aircraft travels in the 5 seconds after it passes the anti-aircraft gun. The problem gives us two key pieces of information:

• The speed of the aircraft is 335 m/s.
• The time duration after passing the gun is 5 seconds.

To find the distance traveled, we use the formula for distance:

Distance = Speed × Time

Plugging in the given values:

Distance = 335 m/s × 5 s

Calculating this, we get:

Distance = 1675 meters

This means the aircraft is 1675 meters away from the point where it passed the anti-aircraft gun after 5 seconds.

Answer Details

When a charged ebonite rod is brought near a charged glass rod, there will be attraction. This is because charged objects obey the fundamental principle of electrostatics, which states that opposite charges attract each other while like charges repel each other.

An ebonite rod typically acquires a negative charge when rubbed with fur, as it gains electrons. In contrast, a glass rod usually acquires a positive charge when rubbed with silk, as it loses electrons. Therefore, when these two objects, one negatively charged and the other positively charged, are brought near each other, the opposite charges will attract.

Answer Details

To convert temperatures from Celsius to Fahrenheit, we use the formula:

F = (C × 9/5) + 32

Here, F represents the temperature in Fahrenheit, and C represents the temperature in Celsius.

Let's use this formula to convert 60ºC to Fahrenheit:

F = (60 × 9/5) + 32

First, multiply 60 by 9/5:

60 × 9/5 = 108

Next, add 32 to 108:

108 + 32 = 140

Therefore, 60ºC is equal to 140ºF.

Answer Details

To find the density of the fluid, we need to apply the principle of floatation, which states that the weight of the fluid displaced by the submerged part of the object is equal to the weight of the object. Let's walk through the steps:

Step 1: Understand the volume submerged

The hydrometer has a total volume of 2y x 10^-5 m³. It floats with 20% of its volume above the fluid. Hence, 80% of its volume is submerged in the fluid.

Submerged Volume, V_sub = (0.80) x (2y x 10^-5 m³) = 1.6y x 10^-5 m³

Step 2: Apply the principle of floatation

The weight of the fluid displaced equals the weight of the hydrometer.

Weight of hydrometer = Mass x Gravity = y kg x g (where g is the acceleration due to gravity). For the purpose of calculations, g can be considered as 9.81 m/s².

Weight of displaced fluid = Density of fluid (ρ_fluid) x Submerged Volume x g

According to the principle of floatation:

y x g = ρ_fluid x 1.6y x 10^-5 m³ x g

g is common on both sides and can be canceled out:

y = ρ_fluid x 1.6y x 10^-5

Step 3: Solving for the density of the fluid

ρ_fluid = y / (1.6y x 10^-5)

The y on both numerator and denominator cancels out:

ρ_fluid = 1 / (1.6 x 10^-5)

ρ_fluid = 6.25 x 10⁴ kg/m³

Thus, the density of the fluid is 6.25 x 10⁴ kg/m³.

Answer Details

To solve this problem, we need to understand the relationship between pressure, volume, and temperature of a gas. The relevant law here is the **Combined Gas Law**, which is expressed as:

(P1 * V1) / T1 = (P2 * V2) / T2

Where:

• P1 is the initial pressure
• V1 is the initial volume
• T1 is the initial temperature in Kelvin
• P2 is the final pressure
• V2 is the final volume
• T2 is the final temperature in Kelvin

In the given problem:

• The initial temperature, T1, is 27ºC, which is 300K (since we convert to Kelvin by adding 273).
• The final temperature, T2, is 127ºC, which is 400K.
• The pressure is doubled, so P2 = 2 * P1.

Applying the Combined Gas Law:

(P1 * V1) / 300 = (2 * P1 * V2) / 400

Simplifying this equation:

V1/300 = 2V2/400

Multiply both sides by 400 to clear the fraction:

400 * V1 / 300 = 2 * V2

Which further simplifies to:

(4/3) * V1 = 2 * V2

Dividing both sides by 2:

(2/3) * V1 = V2

This shows that the final volume, V2, is **2/3 of the initial volume, V1**. Therefore, the volume of the gas will **decrease by 1/3**.

Answer Details

When it comes to a model rocket, it is crucial to understand the different parts that make up the rocket and their functions:

• The Body Tube: This is the main frame of the rocket. It holds all the other components together and serves as the backbone of the rocket.
• The Nose Cone: This is the pointed part at the top of the rocket. It is designed to reduce aerodynamic drag and also aids in stabilizing the rocket during flight.
• The Fin: Fins are attached at the lower end of the rocket. They help stabilize the rocket's flight path by reducing wobble and assisting in maintaining a straight trajectory.

Now, “Not recovery devices” is listed among the options. A recovery device is actually a part of a model rocket system. Common recovery devices include parachutes or streamers that deploy after the rocket reaches its peak altitude, allowing it to return safely to the ground. Such devices are indeed part of a model rocket design.

Therefore, the option “Not recovery devices” itself is not recognized as a part of a model rocket. Instead, the sentence is stating that they are not part of the main components, which implies it's indicative rather than being the name of a component. Hence, it does not pertain to a single component like the body tube, nose cone, or fins.

Answer Details

The mass of an object can be calculated using the formula:

Mass = Density × Volume

In this case, we need to find the mass of a solid cube of aluminum. Given:

• Density of aluminum = 2700 kg/m³
• Edge length of the cube = 1.5 cm

First, we need to calculate the volume of the cube. The volume V of a cube with edge length a is given by:

V = a³

Substitute the edge length:

V = (1.5 cm)³ = 1.5 × 1.5 × 1.5 cm³ = 3.375 cm³

Since the density is given in kg/m³, we should convert the volume from cm³ to m³. There are 1,000,000 cm³ in 1 m³, so:

Volume in m³ = 3.375 cm³ × (1 m³/1,000,000 cm³) = 3.375 × 10^-6 m³

Now, use the mass formula:

Mass = Density × Volume

Mass = 2700 kg/m³ × 3.375 × 10^-6 m³

This equals:

Mass = 9.1125 × 10^-3 kg

Convert kg to grams (since 1 kg = 1000 g):

Mass = 9.1125 grams

So, the mass of the cube is approximately 9.1 g. Thus, the correct answer is 9.1 g.

Answer Details

The energy stored in the capacitor = 12 $\frac{1}{2}$q2C $\frac{q^2}{C}$

Where C = 2F, q = 3C

=  12 $\frac{1}{2}$322 $\frac{3^2}{2}$ = 94 $\frac{9}{4}$ = 2.25J

Answer Details

The power of a lens is a measure of its ability to converge or diverge light. It is defined as the reciprocal (or inverse) of the focal length of the lens. The formula for calculating the power (P) of a lens in diopters (D) is given by:

P = 1/f

where:

• P is the power of the lens in diopters (D).
• f is the focal length of the lens in meters.

In this case, the focal length given is 20 cm. To apply the formula, we first need to convert this focal length into meters because the diopter is the reciprocal of the focal length in meters:

f = 20 cm = 0.20 m

Now, substitute the focal length in meters into the formula for power:

P = 1 / 0.20

P = 5.00 D

Thus, the power of the convex lens is 5.00 diopters. This indicates that the lens is capable of converging light at a distance of 5.00 meters.

Answer Details

The energy in a moving car is an example of kinetic energy.

To explain simply, **energy** is the ability to do **work** or cause **change**. There are different forms of energy, and **kinetic energy** is one of them. It is defined as the energy possessed by an object due to its motion.

When a car is moving, it possesses **kinetic energy** because its components are in **motion**. This motion energy allows the car to do tasks, such as transporting people or goods from one place to another. The faster the car moves, the greater its **kinetic energy**, and thus it can make a larger impact or do more work.

In contrast, energy forms like **mechanical energy** is a combination of both kinetic and potential energy; **electrical energy** is associated with electrical charge movement, while **potential energy** is related to the position or condition of an object (like a car parked on a hill). Therefore, the specific type of energy from a moving car is **kinetic energy**.

Answer Details

A pinhole camera is a simple camera device that uses a tiny hole to project an inverted image of the scene in front of it onto a surface at the back of the camera. When you diminish the hole of a pinhole camera, meaning you make the hole smaller, a few effects occur on the resulting image. Here’s what happens:

• Firstly, when the pinhole is smaller, less light enters the camera. This results in the image becoming darker.
• Additionally, with a smaller hole, the path of light rays becomes narrower which helps to reduce blurring and overlaps from being out of focus. Consequently, the image becomes sharper.

Therefore, reducing the size of the pinhole in a pinhole camera results in the image becoming both darker and sharper.

Answer: II only (The image becomes sharper.)

Answer Details

To understand when a vapor is considered saturated, it is crucial to consider the rates of two significant processes: evaporation and condensation. **Evaporation** is the process where liquid molecules escape into the vapor phase, and its rate is denoted as **y**. On the other hand, **condensation** is the process where vapor molecules return to the liquid phase, with its rate denoted as **x**.

A vapor is said to be **saturated** when the rate of evaporation of the liquid is equal to the rate of condensation of the vapor. In simpler terms, the number of molecules leaving the liquid to become vapor is exactly equal to the number of molecules returning from the vapor to the liquid.

In mathematical terms, this condition can be described as **x = y**. Under this condition, the system reaches a dynamic equilibrium, and the vapor pressure of the system is at its maximum for the given temperature. At this point, the vapor cannot accommodate any more molecules, and thus, the vapor is in a saturated state.

Answer Details

To calculate the speed of the wave, we need to understand some fundamental wave properties: **wavelength**, **frequency**, and **wave speed**.

1. **Wavelength (\( \lambda \))**: The wavelength is the distance between two successive crests of a wave. In this case, the wavelength is given as **0.25 meters**.

2. **Frequency (\( f \))**: Frequency is the number of complete oscillations or cycles that occur per second. It is given that a particle on the surface of the water makes **four complete vertical oscillations in one second**. So, the frequency is **4 Hz (hertz)**.

3. **Wave Speed (\( v \))**: The speed of a wave is calculated using the formula:

\( v = f \times \lambda \)

Where:

\( v \) is the wave speed,

\( f \) is the frequency, and

\( \lambda \) is the wavelength.

Substitute the given values into the formula:

\( v = 4 \text{ Hz} \times 0.25 \text{ m} \)

\( v = 1 \text{ m/s} \)

Therefore, the **speed of the wave** is 1 m/s.

Answer Details

The formation of cilia and flagella in living cells is primarily carried out with the help of **centrioles**.

Here's a simple explanation:

Centrioles are cylindrical structures made up of microtubules. They are found in eukaryotic cells and play a critical role in cell division and the organization of the cell's cytoskeleton. However, their role extends beyond this to the formation of the basal bodies which seed the growth of cilia and flagella.

Cilia and flagella are microscopic, hair-like structures that protrude from the surface of certain eukaryotic cells. They are primarily involved in movement. Cilia often work like tiny oars, moving fluid across the cell's surface or propelling single-celled organisms. Flagella are typically longer and move in a whip-like fashion to propel cells, such as sperm cells.

Here's how centrioles contribute to the formation of these structures:

1. **Basal Body Formation**: Each cilium or flagellum grows out from a structure known as a basal body. The basal body is derived from the centrioles. During this process, a centriole migrates to the cell's surface and acts as a nucleation site for the growth of microtubules, which in turn form the structural core of cilia and flagella.

2. **Microtubule Organization**: The centrioles help organize microtubules in a "9+2" arrangement, which is characteristic of cilia and flagella. This refers to nine pairs of microtubules forming a ring around two central microtubules, giving these structures both stability and flexibility for movement.

Thus, centrioles are crucial as they provide the groundwork for the formation and proper functioning of cilia and flagella. They ensure that these structures are assembled correctly and are able to carry out their roles in cell movement and fluid transport.

Answer Details

When you insert a sheet of an insulating material between the plates of an air capacitor, the capacitance will increase.

Here's why:

• Capacitance is a measure of a capacitor's ability to store charge per unit voltage across its plates.
• The formula for capacitance (C) is:

C = ε₀ * (εr) * (A/d)

• Where:
  • ε₀ is the permittivity of free space (a constant).
  • εr is the relative permittivity (also known as the dielectric constant) of the material between the plates.
  • A is the area of one of the plates.
  • d is the separation between the plates.
• When an insulating material (also known as a dielectric) is inserted between the plates, its εr is greater than that of air (which is 1).
• This increases the overall capacitance of the capacitor since the product of ε₀ and εr is larger than ε₀ alone.

Therefore, inserting an insulating material as a dielectric enhances the capacitor's ability to store charge, ultimately resulting in an increase in capacitance.

Answer Details

When capacitors are connected in series, the formula to find their combined capacitance \(C_{\text{total}}\) is given by:

\[ \frac{1}{C_{\text{total}}} = \frac{1}{C_1} + \frac{1}{C_2} \]

where \(C_1\) and \(C_2\) are the capacitances of the individual capacitors. In this case, \(C_1 = 0.0003 \, \mu\text{F}\) and \(C_2 = 0.0006 \, \mu\text{F}\).

First, calculate the reciprocal of each capacitance:

\[ \frac{1}{C_1} = \frac{1}{0.0003} \]

\[ \frac{1}{C_2} = \frac{1}{0.0006} \]

Calculating each value:

\[ \frac{1}{0.0003} = \frac{10^6}{3} \] and \[ \frac{1}{0.0006} = \frac{10^6}{6} \]

Now, add these values together:

\[ \frac{1}{C_{\text{total}}} = \frac{10^6}{3} + \frac{10^6}{6} = \frac{10^6 \times 2}{6} + \frac{10^6 \times 1}{6} = \frac{10^6 \times 3}{6} = \frac{10^6}{2} \]

Finally, take the reciprocal of the resulting value to find \(C_{\text{total}}\):

\[ C_{\text{total}} = \frac{2}{10^6} = 0.0002 \, \mu\text{F} \]

So, the combined capacitance of the two capacitors in series is 0.0002 μF.

Answer Details

The diaphragm in a camera is similar to the iris in the human eye.

Here's a simple explanation:

• Both the diaphragm in a camera and the iris in the eye control the amount of light that enters. The diaphragm adjusts the size of the aperture, which is the opening that allows light to hit the camera's sensor.
• Similarly, the iris adjusts the size of the pupil, which is the opening that allows light to enter the eye and reach the retina.
• The camera's diaphragm is responsible for creating different aperture sizes, just as the iris changes the size of the pupil in different lighting conditions.
• In bright light, both the diaphragm and the iris make their respective openings smaller to reduce the amount of light entering, protecting the camera's sensor and the eye's retina respectively.
• Conversely, in low light conditions, both open wider to allow more light in, enhancing clarity and visibility.

In summary, the iris acts like a natural diaphragm, regulating the light that passes through the eye, much like the diaphragm does in a camera.

Answer Details

The dimension of power in physics is expressed in terms of the base units of mass (M), length (L), and time (T). Power is the rate at which work is done or energy is transferred over time, and it has the unit of watt (W) which is equivalent to one joule per second.

To derive the dimension of power:

1. Work has the dimension of energy, which is force applied over a distance. The dimension of work (or energy) is M L² T^-2 because force has the dimension M L T^-2 and distance adds another L.

2. Since power is work done per unit time, you would divide the dimension of work by time (T).

Thus, the dimensional formula for power is:

M L² T^-3

Answer Details

To understand which of these gas laws is equivalent to work done, we must first understand the basic concept of work in the context of gases. For gases, work is done when there is a change in volume under pressure, typically expressed as W = P ΔV, where W is work, P is pressure, and ΔV is the change in volume.

Let's consider the given gas laws:

• Charle's law states that the volume of a gas is directly proportional to its temperature at constant pressure.
• Pressure law (often referred to as Gay-Lussac's law) says that the pressure of a gas is directly proportional to its temperature at constant volume.
• Boyle's law states that the pressure of a gas is inversely proportional to its volume at constant temperature. In equation form, this is P₁V₁ = P₂V₂.
• Gay-Lussac's law is another name for the Pressure law.

Among these, Boyle's law relates directly to work done because it involves a change in volume at constant temperature, implying that work occurs as a gas expands or compresses. The equation P₁V₁ = P₂V₂ is foundational for calculating work done in reversible processes, which aligns with the expression for work done on a gas, W = P ΔV. Thus, **Boyle's law** is most directly connected to the concept of work done on a gas.

Answer Details

To solve this problem, we first need to understand the principle behind a potentiometer. A potentiometer is a device used to measure the electromotive force (e.m.f) of a cell by comparing it with a known voltage. The balance length on a potentiometer corresponds to a proportional measurement of the e.m.f.

Let's denote:

- \( V_1 \): the e.m.f of the first cell = 3.06V

- \( l_1 \): the balance length for the first cell = 75 cm

- \( V_2 \): the e.m.f of the second cell = 2.295V

- \( l_2 \): the balance length for the second cell (which we need to find)

The basic relationship for a potentiometer is given by:

\( V_1 / V_2 = l_1 / l_2 \)

Substituting the given values:

\( 3.06 / 2.295 = 75 / l_2 \)

We need to solve for \( l_2 \):

\( l_2 = (2.295 \times 75) / 3.06 \)

Now, calculating the above expression:

\( l_2 = 171.975 / 3.06 \approx 56.26 \) cm

Therefore, the new balance length for the cell with an e.m.f of 2.295V is approximately 56.26 cm.

Answer Details

The zone labelled II is called the littoral zone.

To explain: The littoral zone is a part of a body of water that is close to the shore. It is typically characterized by abundant sunlight and nutrient availability, making it a highly productive area for aquatic plants and animals. This zone supports various forms of life such as algae, small fish, and invertebrates. The key feature of the littoral zone is its proximity to the shoreline, where sunlight can penetrate to the bottom, allowing for photosynthesis to occur.

Answer Details

To solve this problem, we need to calculate the specific latent heat of vaporization of the liquid. The specific latent heat of vaporization, denoted as \(L\), is defined as the amount of heat required to convert 1 kilogram of a liquid into a gas at constant temperature and pressure. The formula for specific latent heat of vaporization is given by:

L = \(\frac{Q}{m}\)

Where:

• Q is the heat supplied to the liquid (in joules)
• m is the mass of the liquid that is evaporated (in kilograms)

First, we need to calculate the total heat energy \(Q\) generated by the resistor. The heat produced by an electrical resistor can be calculated using the formula:

Q = I^2Rt

Where:

• I is the current (in amperes)
• R is the resistance (in ohms)
• t is the time for which current is flowing (in seconds)

Given:

• I = 10 A
• R = 2 Ω
• t = 20 s

Substituting these values into the formula for Q:

Q = (10^2) * 2 * 20 = 100 * 2 * 20 = 4000 J

Now that we have the total heat energy supplied, let's calculate the specific latent heat of vaporization:

Given that the mass \(m\) of the liquid evaporated is \(5 \times 10^{-3}\) kg, we can substitute the values into the formula for \(L\):

L = \(\frac{4000}{5 \times 10^{-3}} = \frac{4000}{0.005} = 800,000 J/kg\)

Therefore, the specific latent heat of vaporization of the liquid is 8.0 x 10⁵ J/kg.

Answer Details

A thermometer that relies on the **thermometric property** of **change in volume with temperature** is the **Liquid-in-glass thermometer**.

Here is why:

1. **Construction**: A liquid-in-glass thermometer consists of a **glass tube** that encloses a small reservoir filled with a **thermometric liquid**, typically mercury or colored alcohol.

2. **Principle of Operation**: As the **temperature** changes, the **volume of the liquid** inside the tube changes. When the temperature rises, the liquid **expands** and moves up the tube. Conversely, when the temperature decreases, the liquid **contracts** and moves down the tube.

3. **Scale Calibration**: The thermometer has graduations marked along the tube, allowing the user to read the temperature by observing the level of the liquid against these scale markings.

Therefore, the liquid-in-glass thermometer operates on the principle that the **volume of a liquid changes with temperature**, making it the correct answer.

Answer Details

Friction due to air mass, also known as air resistance or drag, can be reduced by a concept called **streamlining**.

**Streamlining** refers to the shaping of an object in such a way that it allows air to flow smoothly around it, minimizing turbulence and reducing drag. When air flows smoothly over an object without much disturbance, there is less resistance, and the object can move more easily through the air.

Think of it like how a bullet or a fast-moving car is designed. They have a sleek, smooth shape that cuts through the air with minimal effort. This principle is applied in designing cars, airplanes, and even boats to enhance their efficiency and speed by reducing the friction with the air or water they move through.

Answer Details

To solve this problem, we need to understand the relationship between tension and frequency in a sonometer wire. The frequency of a vibrating string, such as one in a sonometer, is directly proportional to the square root of the tension in the string. Mathematically, this relationship is expressed as:

f ∝ √T

Where f is the frequency and T is the tension. In the given problem, the original frequency is 50 Hz, and the tension is increased to four times its original value. Let's analyze how this change in tension affects the frequency:

- Original tension = T

- New tension = 4T

Substitute the new tension into the formula:

f_new = 50 Hz × √(4T/T)

Simplify the equation:

f_new = 50 Hz × √4

f_new = 50 Hz × 2

f_new = 100 Hz

Thus, when the tension is four times the original tension, the new frequency of the sonometer's fundamental note becomes 100 Hz.

Answer Details

To calculate the electric field intensity due to a charge, we need to use the formula:

Electric Field Intensity (E) = Force (F) / Charge (q)

In this problem, we are given that the force (F) is 8 Newtons (N) and the charge (q) is 4 microcoulombs (μC). First, we need to convert the charge from microcoulombs to coulombs:

1 microcoulomb (μC) = 1 x 10^-6 coulombs (C)

Therefore, 4 μC = 4 x 10^-6 C.

Now we can use the formula to find the electric field intensity:

E = F / q

E = 8 N / (4 x 10^-6 C)

E = 8 / 4 x 10⁶

E = 2 x 10⁶

Thus, the value of the electric field intensity is 2 x 10⁶ N/C.

Answer Details

To calculate the percentage relative humidity of the air, we use the relationship between the saturation vapour pressure (SVP) and the actual vapour pressure. The formula for relative humidity is:

Relative Humidity (%) = (Actual Vapour Pressure / Saturation Vapour Pressure) * 100

In this problem, the "dew point" refers to the temperature at which air becomes saturated with moisture and water begins to condense. At the dew point, the actual vapour pressure is equal to the saturation vapour pressure at that dew point temperature.

From the problem, we have:

• Saturation Vapour Pressure (SVP) at 33ºC = 13.5 mmHg
• Saturation Vapour Pressure (SVP) at 7ºC (which is the dew point) = 7.3 mmHg

The actual vapour pressure of the air is equal to the SVP at the dew point, which is 7.3 mmHg.

Now we calculate the percentage relative humidity using the formula:

Relative Humidity (%) = (7.3 mmHg / 13.5 mmHg) * 100

Carrying out the calculation:

Relative Humidity (%) = (7.3 / 13.5) * 100 = 0.5407 * 100 = 54.07%

Rounding to the nearest whole number, we get **54%**. Therefore, the percentage relative humidity of the air is 54%.

Answer Details

The mouthpart adapted for piercing and sucking is found in the mosquito. Mosquitoes have a specialized mouth structure called a proboscis. This proboscis is long and slender, allowing mosquitoes to puncture the skin of their hosts and suck blood. The proboscis is a complex structure that contains several needle-like parts that make the piercing and sucking process efficient and effective.

Answer Details

The property by which a material returns to its original shape after the removal of force is called Elasticity.

Let's break it down:

Elasticity: This is a property of a material that allows it to return to its original shape or size after the force that caused deformation is removed. Think of a rubber band—you can stretch it, but once you let it go, it snaps back to its initial shape.

Ductility: This property refers to a material's ability to be stretched into a wire. For example, materials like copper are ductile because they can be drawn into thin wires without breaking.

Malleability: This is a material's ability to withstand deformation under compressive stress. It is the property that allows metals to be hammered or rolled into thin sheets. Gold is a good example of a malleable metal.

Plasticity: This property describes the material's ability to undergo permanent deformation without breaking. When a plastic region is reached, the material will not return to its original shape after the removal of force.

Therefore, when we speak of a material returning to its original shape after the removal of force, we are specifically referring to Elasticity.

Answer Details

To determine the quantity of heat required to melt ice, we use the formula for latent heat:

Q = m × L,

where:

• Q is the heat energy absorbed or released (in joules).
• m is the mass of the substance (in kilograms).
• L is the specific latent heat (in joules per kilogram, J/Kg).

For this problem, we have:

• Mass of ice, m = 0.2 kg
• Specific latent heat of ice, L = 3.4 × 10⁵ J/Kg

Now, substitute these values into the formula:

Q = 0.2 kg × 3.4 × 10⁵ J/kg

Calculate the product:

Q = 0.68 × 10⁵ J

To express this in standard scientific notation, it can be rewritten as:

Q = 6.8 × 10⁴ J

Thus, the quantity of heat required to melt 0.2 kg of ice is 6.8 × 10⁴ J.

Answer Details

An ideal transformer is a hypothetical concept used in electrical engineering to simplify the analysis of real transformers. In an ideal transformer, several assumptions are made to avoid losses and inefficiencies. Here's what an ideal transformer has:

No flux leakage: In an ideal transformer, it is assumed that all the magnetic flux generated in the primary coil is perfectly linked with the secondary coil. This means there is no flux leakage. This assumption ensures maximum efficiency, as all the energy is transferred from the primary to the secondary coil without losses.

Let's briefly discuss the other concepts to understand why they don't pertain to an ideal transformer:

Maximum primary resistance: In an ideal transformer, the resistance of the windings is assumed to be zero. If the primary has maximum resistance, it would result in power loss due to the resistance, contradicting the idea of an ideal transformer.

Hysteresis: This refers to the energy loss that happens in the core material due to the cyclic magnetization and demagnetization processes. An ideal transformer assumes there is no hysteresis loss, meaning the core material does not absorb any energy during these cycles.

Eddy current: These are loops of electric current induced within conductors by a changing magnetic field, which can cause significant energy loss. In an ideal transformer, it is assumed that there are no eddy currents, hence no energy loss due to this effect.

In summary, an ideal transformer is characterized by having no flux leakage, and it assumes that there are no losses due to resistance, hysteresis, or eddy currents. This makes the ideal transformer a perfect, lossless device for the purposes of theoretical analysis.

Answer Details

The diagram is that of the virus. Viruses are obligate parasites, meaning they can't produce their own energy or proteins. They enter the host cell and use the cell's machinery to make their own nucleic acids and proteins. Viruses also use the host cell's lipids and sugar chains to create their membranes and glycoproteins. This parasitic replication can severely damage the host cell, which can lead to disease or cell death. They usually enter your body through your mucous membranes. These include your eyes, nose, mouth, penis, vagina and anus.

Viruses are a unique type of organism that are not plants, animals, or bacteria. They are often classified in their own kingdom. However, for the sake of the question, since most of their attributes and metabolic activities are more of the bacteria, we'll go with option A - Monera

Answer Details

Newton's Law of Cooling states that the rate of heat loss of an object is directly proportional to the difference in temperature between the object and its surroundings, provided that this temperature difference is small.

Therefore, this law is only valid within a small temperature range.

Answer Details

The part of the inner ear that is responsible for hearing is the cochlea.

The inner ear is a complex structure, and each of its components serves different functions. Let me break it down further:

• Cochlea: This is a spiral-shaped, fluid-filled structure that resembles a snail shell. It is the main organ responsible for hearing. Sound waves enter the ear, travel through the ear canal, and cause the eardrum to vibrate. These vibrations are then transmitted to the cochlea through tiny bones in the middle ear. Inside the cochlea, these vibrations create waves in the fluid, stimulating tiny hair cells. The movement of these hair cells converts the sound waves into electrical signals, which are sent to the brain through the auditory nerve, allowing us to perceive sound.


• Sacculus and Utriculus: These structures primarily deal with balance rather than hearing. They are part of the vestibular system, which helps the body maintain its balance and spatial orientation.


• Ampullae: These are located in the semicircular canals of the inner ear and also play a role in balance. They contain sensory hair cells that detect rotational movement of the head.

Thus, the cochlea is the crucial component of the inner ear responsible for converting sound vibrations into nerve signals, making it central to the process of hearing.